收藏本站
Core Configuration
Table 4-3. Operating Mode Register (OMR) Bit Definitions (Continued)
Bit Number
14
Bit Name
APD
Reset Value
0
Description
Address Attribute Priority Disable
Disables the priority assigned to the Address Attribute signals (AA[0–3]).
When APD = 0 (default setting), the four Address Attribute signals each
have a certain priority: AA3 has the highest priority, AA0 has the lowest
priority. Therefore, only one AA signal can be active at one time. This
allows continuous partitioning of external memory; however, certain
functions, such as using the AA signals as additional address lines,
require the use of additional interface hardware. When APD is set, the
priority mechanism is disabled, allowing more than one AA signal to be
active simultaneously. Therefore, the AA signals can be used as
additional address lines without the need for additional interface
hardware. For details on the Address Attribute Registers, see
Section 4.6.3 , Address Attribute Registers (AAR[0–3]), on page 4-25.
13
ABE
0
Asynchronous Bus Arbitration Enable
Eliminates the setup and hold time requirements for BB and BG, and
substitutes a required non-overlap interval between the deassertion of on e
BG input to a DSP56300 family device and the assertion of a second BG
input to a second DSP56300 family device on the same bus. When the
ABE bit is set, the BG and BB inputs are synchronized. This
synchronization causes a delay between a change in BG or BB until this
change is actually accepted by the receiving device.
12
BRT
0
Bus Release Timing
Selects between fast or slow bus release. If BRT is cleared, a Fast Bus
Release mode is selected (that is, no additional cycles are added to the
access and BB is not guaranteed to be the last Port A pin that is tri-stated
at the end of the access). If BRT is set, a Slow Bus Release mode is
selected (that is, an additional cycle is added to the access, and BB is the
last Port A pin that is tri-stated at the end of the access).
11
TAS
0
TA Synchronize Select
Selects the synchronization method for the input Port A pin—TA (Transfer
Acknowledge). At operating frequencies ≤ 100 MHz, TA can operate
synchronously (with respect to CLKOUT) or asynchronously depending
on the setting of the TAS bit in the Operating Mode Register (OMR). If
synchronous mode is selected, the user is responsible for ensuring that
TA transitions occur synchronous to CLKOUT to ensure correct operation.
Synchronous operation is not supported above 100 MHz; when using TA,
the OMR[TAS] bit must be set to synchronize the TA signal with the
internal clock.
10
BE
0
Cache Burst Mode Enable
Enables/disables Burst mode in the memory expansion port during an
instruction cache miss. If the bit is cleared, Burst mode is disabled and
only one program word is fetched from the external memory when an
instruction cache miss condition is detected. If the bit is set, Burst mode is
enabled, and up to four program words are fetched from the external
memory when an instruction cache miss is detected.
DSP56311 User’s Manual, Rev. 2
4-12
Freescale Semiconductor
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*
相关PDF资料
DSPAUDIOEVMMB1E BOARD MOTHER DSP563XX
DSPIC30F2010 DEVELOPMENT KIT KIT DEV EMBEDDED C
DSTRM-KT-0181A DSTREAM DEBUG AND TRACE UNIT
DSUT1CSU SURGE SUPPR NETWORK W/GROUND
DTEL2 SURGE SUPPRESSOR PHONE RJ11/RJ45
DV003001 PROGRAMMER PICSTART PLUS 16C/17C
DV164035 MPLAB ICD3 IN-CIRC DEBUGGER
DV164039 KIT DEV PIC24FJ256DA210
相关代理商/技术参数
DSP56311EVMIG_D 制造商:未知厂家 制造商全称:未知厂家 功能描述:DSP56311EVMIG DSP56311EVM Sample Code
DSP56311EVMUM 制造商:未知厂家 制造商全称:未知厂家 功能描述:DSP56311 Evaluation Module Hardware Reference Manual
DSP56311FACT 制造商:未知厂家 制造商全称:未知厂家 功能描述:DSP56311 Higher performance programmable DSP for demanding voice and data applications
DSP56311UM 制造商:未知厂家 制造商全称:未知厂家 功能描述:DSP56311 24-Bit Digital Signal Processor Users Manual
DSP56311UMAD 制造商:未知厂家 制造商全称:未知厂家 功能描述:DSP56311 Users Manual Addendum
DSP56311VF150 功能描述:数字信号处理器和控制器 - DSP, DSC 150Mhz/300MMACS 150Mhz EFCOP RoHS:否 制造商:Microchip Technology 核心:dsPIC 数据总线宽度:16 bit 程序存储器大小:16 KB 数据 RAM 大小:2 KB 最大时钟频率:40 MHz 可编程输入/输出端数量:35 定时器数量:3 设备每秒兆指令数:50 MIPs 工作电源电压:3.3 V 最大工作温度:+ 85 C 封装 / 箱体:TQFP-44 安装风格:SMD/SMT
DSP56311VF150B1 功能描述:数字信号处理器和控制器 - DSP, DSC 24 BIT DSP RoHS:否 制造商:Microchip Technology 核心:dsPIC 数据总线宽度:16 bit 程序存储器大小:16 KB 数据 RAM 大小:2 KB 最大时钟频率:40 MHz 可编程输入/输出端数量:35 定时器数量:3 设备每秒兆指令数:50 MIPs 工作电源电压:3.3 V 最大工作温度:+ 85 C 封装 / 箱体:TQFP-44 安装风格:SMD/SMT
DSP56311VF150R2 功能描述:数字信号处理器和控制器 - DSP, DSC 24 BIT DSP RoHS:否 制造商:Microchip Technology 核心:dsPIC 数据总线宽度:16 bit 程序存储器大小:16 KB 数据 RAM 大小:2 KB 最大时钟频率:40 MHz 可编程输入/输出端数量:35 定时器数量:3 设备每秒兆指令数:50 MIPs 工作电源电压:3.3 V 最大工作温度:+ 85 C 封装 / 箱体:TQFP-44 安装风格:SMD/SMT